USB_CTRL_REQUEST(9S) Data Structures for Drivers USB_CTRL_REQUEST(9S)

usb_ctrl_req, usb_ctrl_req_t, usb_ctrl_request - USB control pipe request structure

#include <sys/usb/usba.h>

illumos DDI specific (illumos DDI)

A control request is used to send device commands (or requests) and to read status. Please refer to Section 5.5 of the USB 2.0 specification for information on control pipes. For information on formatting requests, see Section 9.3 of the USB 2.0 specification. The USB 2.0 specification is available at www.usb.org.

The fields in the usb_ctrl_req_t are used to format a control request:




  uint8_t      ctrl_bmRequestType; /* characteristics of request */


  uint8_t      ctrl_bRequest;  /* specific request             */


  uint16_t     ctrl_wValue;    /* varies according to request  */


  uint16_t     ctrl_wIndex;    /* index or offset              */


  uint16_t     ctrl_wLength;   /* number of bytes to xfer      */


  mblk_t       *ctrl_data;     /* data for the data phase  */


                               /* IN or OUT: allocated by client */


  uint_t       ctrl_timeout;   /* time until  USBA framework */


                               /* retires req, in seconds */


                               /* If set to zero, defaults to 5 sec */


  usb_opaque_t    ctrl_client_private; /* client private info */


  usb_req_attrs_t ctrl_attributes; /* attrib. for this req */


  /* Normal callback function, called upon completion. */


  void       (*ctrl_cb)(


                 usb_pipe_handle_t ph, struct usb_ctrl_req *req);


  /* Exception callback function, for error handling. */


  void       (*ctrl_exc_cb)(


                 usb_pipe_handle_t ph, struct usb_ctrl_req *req);


  usb_cr_t   ctrl_completion_reason; /* overall success status */


                                  /* See usb_completion_reason(9S) */


  usb_cb_flags_t  ctrl_cb_flags; /* recovery done by callback hndlr */


                                /* See usb_callback_flags(9S) */

Request attributes define special handling for transfers. The following attributes are valid for control requests:

USB_ATTRS_SHORT_XFER_OK

Accept transfers where less data is received than expected.

USB_ATTRS_AUTOCLEARING

Have USB framework reset pipe and clear functional stalls automatically on exception.

USB_ATTRS_PIPE_RESET

Have USB framework reset pipe automatically on exception.

Please see usb_request_attributes(9S) for more information.

The following definitions directly pertain to fields in the USB control request structure. (See Section 9.3 of the USB 2.0 specification.)


Direction bitmasks of a control request's ctrl_bmRequestType field
(USB 2.0 spec, section 9.3.1)


     USB_DEV_REQ_HOST_TO_DEV     | Host to device direction


     USB_DEV_REQ_DEV_TO_HOST     | Device to host direction


     USB_DEV_REQ_DIR_MASK        | Bitmask of direction bits
Request type bitmasks of a control request's ctrl_bmRequestType field
(USB 2.0 spec, section 9.3.1)


     USB_DEV_REQ_TYPE_STANDARD   | USB 2.0 defined command


                                 | for all USB devices


     USB_DEV_REQ_TYPE_CLASS      | USB 2.0 defined


                                 | class-specific command


     USB_DEV_REQ_TYPE_VENDOR     | Vendor-specific command


     USB_DEV_REQ_TYPE_MASK       | Bitmask of request type bits
Recipient bitmasks of a control request's ctrl_bmRequestType field
(USB 2.0 spec, section 9.3.1)


     USB_DEV_REQ_RCPT_DEV        | Request is for device


     USB_DEV_REQ_RCPT_IF         | Request is for interface


     USB_DEV_REQ_RCPT_EP         | Request is for endpoint


     USB_DEV_REQ_RCPT_OTHER      | Req is for other than above


     USB_DEV_REQ_RCPT_MASK       | Bitmask of request recipient bits
Standard requests (USB 2.0 spec, section 9.4)


     USB_REQ_GET_STATUS          | Get status of device, endpoint


                                 |or interface (9.4.5)


     USB_REQ_CLEAR_FEATURE       | Clear feature specified by


                                 |wValue field (9.4.1)


     USB_REQ_SET_FEATURE         | Set feature specified by


                                 |       wValue field (9.4.9)


     USB_REQ_SET_ADDRESS         | Set address specified by


                                 |       wValue field (9.4.6)


     USB_REQ_GET_DESCR           | Get descr for item/idx in


                                 |       wValue field (9.4.3)


     USB_REQ_SET_DESCR           | Set descr for item/idx in


                                 |       wValue field (9.4.8)


     USB_REQ_GET_CFG             | Get current device


                                 |        configuration (9.4.2)


     USB_REQ_SET_CFG             | Set current device


                                 |        configuration (9.4.7)


     USB_REQ_GET_IF              | Get alternate interface


                                 |       setting (9.4.4)


     USB_REQ_SET_IF              | Set alternate interface


                                 |       setting (9.4.10)


     USB_REQ_SYNC_FRAME          | Set and report an endpoint's


                                 |       sync frame (9.4.11)
Unicode language ID, used as wIndex for USB_REQ_SET/GET_DESCRIPTOR


     USB_LANG_ID                 | Unicode English Lang ID for


                                 | parsing str descr

See attributes(7) for descriptions of the following attributes:

ATTRIBUTE TYPE ATTRIBUTE VALUE
Architecture PCI-based systems
Interface stability Committed

usb_alloc_request(9F), usb_pipe_bulk_xfer(9F), usb_pipe_ctrl_xfer(9F), usb_pipe_intr_xfer(9F), usb_pipe_isoc_xfer(9F), usb_bulk_request(9S), usb_callback_flags(9S), usb_completion_reason(9S), usb_intr_request(9S), usb_isoc_request(9S), usb_request_attributes(9S)

January 5, 2004 OmniOS